Close-up of a CNC-machined steel threaded adapter with milled flats on a dark reflective surface

HSE Documents an Oilfield Equipment Supplier Must Provide

Published:

Summary of the article

This guide covers the HSE documents an oilfield supplier submits for vendor registration: the policy, manual, risk and legal registers, emergency plan, incident, training and audit records, and any ISO 45001 or 14001 certificate. It shows what each one must contain, and how operators check it against the sites and work it claims to cover.

An oilfield equipment supplier provides a health, safety and environment (HSE) document set: a signed HSE policy, the HSE manual, risk and legal registers, an emergency plan, incident records and statistics, training records, audit records and, where held, an ISO 45001 or ISO 14001 certificate with its scope.

How deep the operator's review goes depends on the HSE risk of the scope supplied. IOGP, the International Association of Oil and Gas Producers, sets out that principle in its contracting guidance. The reviewer then checks each document against the site and the activities it claims to cover.

HSE is assessed as its own criterion. A certificate alone does not answer an HSE questionnaire, because operators verify how the system works in practice. If you are putting together a vendor pack for a vendor registration, or checking one as a reviewer, this guide sets out which HSE documents an oilfield supplier is asked for, what each one has to contain and how it is checked. The short version comes first.

What are the HSE documents a supplier must provide, in brief

A supplier's HSE pack contains nine core documents, plus any ISO 45001 or ISO 14001 certificate it holds, and each one is checked against the site and work it claims to cover.

  • The nine documents are the HSE policy, the HSE manual, a hazard and risk register, a legal register, an environmental aspects register, an emergency plan, an incident procedure with statistics, training and competence records, and audit and management review records.
  • Depth follows risk under IOGP 423, so a plant-based manufacturer and a crew on the operator's site are assessed differently.
  • Every injury rate states its base: IOGP uses 1,000,000 hours worked and OSHA uses 200,000 hours worked.
  • A certificate is checked for status, scope and certified site, and IAF CertSearch shows all three for accredited certificates.
  • Risk assessments must match the activities the supplier performs.
  • Operators confirm desktop answers with an audit, and the IOGP 423 capability assessment ends with a verification audit.

Why do operators ask an equipment supplier for HSE documents as well as quality documents

An operator's supplier review covers two separate questions: whether the product is right, which quality records answer, and whether the supplier controls risk to people and the environment, which HSE records answer. Quality documents, such as material test reports, inspection and test plans and test certificates, evidence the product. HSE records evidence the supplier's HSE management system where its work is done.

IOGP (the International Association of Oil and Gas Producers) sets out the industry's common process in IOGP Report 423. It is a risk-based process for managing HSE in a contract environment, covering contractor selection, contract award and every phase of the contract after it. Its supplement, the IOGP 423-01 capability assessment questionnaire, is the contractor HSE questionnaire and scoring system used for an HSE capability assessment.

The IOGP 423-01 questionnaire covers ten elements that follow IOGP 510:

  1. Commitment and accountability
  2. Policies, standards and objectives
  3. Organization, resources and capability
  4. Stakeholders and customers
  5. Risk assessment and control
  6. Asset design and integrity
  7. Plans and procedures
  8. Execution of activities
  9. Monitoring, reporting and learning
  10. Assurance, review and improvement

Shared platforms collect the same evidence as part of supplier qualification. The Achilles Global Energy Network carries a self-assessment module built on IOGP 423 and audits contractors. ISNetworld collects and verifies safety statistics, written programs and training documentation for the clients that hire through it. How much of this a manufacturer is asked for is decided by risk.

How much HSE evidence does a manufacturer need compared with a contractor working on the operator's site

IOGP 423 sets the depth of an HSE capability assessment by the HSE risk of the contracted scope, decided in an HSE risk assessment before any questionnaire is sent. In IOGP's words, "the level of assessment needed is based on the level of risk identified." A manufacturer supplying from its own plant is usually assessed less deeply than a crew working on the operator's site, and the baseline HSE set is still expected.

The approach is risk-based, and IOGP lists what raises the risk: the supplier's experience and past performance, the work location (the client's site or the contractor's own premises), whether its HSE management system has been approved before, open actions, changes to the system or the company, new scopes or regions, and new entrants to the market. IOGP also states that low-risk contracts need no capability assessment, and that a client may choose to assess only high-risk ones.

For an engineered-to-order manufacturer supplying from its own plant, the hazards sit on the supplier's own premises and are controlled by the supplier. The operator's exposure comes through the product and through visits for inspection, witness testing and audit, not through a crew working on the operator's site.

Equipment vendors still receive HSE prequalification questionnaires. Published questionnaires are addressed to companies supplying equipment, materials and services, and some ask separate questions for work that is not a field service. A national oil company vendor registration asks registrants for a baseline HSE set regardless of how deep the later review goes, and a verification audit can still follow.

QuestionContractor working on the operator's siteManufacturer supplying from its own plant
Where the work happensOn the operator's site, alongside its people and plantIn the manufacturer's own plant
Who controls the hazardsShared with the operator, under its permits and site rulesThe manufacturer, under its own HSE management system
What the operator usually asks forA full capability assessment, a job HSE plan and site method statementsThe baseline HSE set, incident statistics and any certificates, with questions on plant activities
What an audit visitsThe work site and the contractor's baseThe plant and its test bay, for example during an inspection or witness test visit

Whatever the depth, the review starts from the baseline set itself.

What is in the core HSE document set, and what must each document contain

The core HSE document set has nine documents, and each one answers a clause of ISO 45001 or ISO 14001 that a reviewer can check. This core document set is the HSE documents list behind the HSE requirements vendor registration forms ask for. The table sets out what each document must contain and what a reviewer checks it against.

DocumentWhat it must containWhat the reviewer checks it against
HSE policyA signed commitment by top management to safe and healthy working conditions, legal compliance, consultation of workers, protection of the environment and continual improvement, with a revision numberISO 45001 clause 5.2 and ISO 14001 clause 5.2. The signature and the legal entity match the company registering.
HSE manual (management system description)The scope, the sites covered, roles and responsibilities, and how each element of the system works, risk control and audit includedThe ten IOGP 423-01 elements. The scope names the manufacturing site.
Hazard identification and risk assessment registerHazards for each activity, a risk rating, controls chosen by the hierarchy of controls, an owner and a review triggerISO 45001 clauses 6.1.2 and 8.1.2
Legal and other requirements register (the legal register)The laws, permits and codes that apply to each site, and the evaluation of compliance against themISO 45001 clauses 6.1.3 and 9.1.2; ISO 14001 clauses 6.1.3 and 9.1.2
Environmental aspects registerThe environmental aspects of the plant's activities (waste, coolants and solvents, coating, emissions, energy use) and which of them are significantISO 14001 clause 6.1.2
Emergency response planScenarios (fire, injury, chemical release, pressure-test failure), roles, contacts and drill recordsISO 45001 clause 8.2 and ISO 14001 clause 8.2, emergency preparedness and response
Incident investigation procedure and statisticsHow incidents and near misses are reported, investigated and corrected; hours worked; injury rates with their baseISO 45001 clause 10.2, and the statistics table in the operator's questionnaire
Training and competence recordsA competence matrix of roles against required training, and the training records behind itISO 45001 clause 7.2
Internal audit and management review recordsThe internal audit schedule, findings, actions and their closure, and management review minutesISO 45001 clauses 9.2 and 9.3

The HSE policy and the HSE manual are two documents. The policy is the signed commitment; the manual describes how the management system delivers it. Certificates are not among the nine, because a certificate is evidence about the system rather than a document of it. The certificate that sits on top of this set is a separate check.

What do ISO 45001 and ISO 14001 certificates evidence, and how do you check one

An ISO 45001 or ISO 14001 certificate evidences that an accredited certification body audited the supplier's management system for a stated scope at stated sites. ISO 45001 covers occupational health and safety management and ISO 14001 covers environmental management, and these are the ISO standards that relate to HSE in a supplier review. A certificate does not prove that any single job is done safely, and it says nothing about sites outside its certified locations.

ISO writes the standards and does not certify anyone. It directs readers to IAF CertSearch, the database run by the International Accreditation Forum (IAF), or to the certification body named on the certificate. IAF CertSearch shows a certificate's validity and status, the standard and scheme, the certificate scope, the certified locations, the issuing certification body and its accreditation body. It holds accredited certifications only. Which other ISO certificates a manufacturer needs, quality certificates included, is a separate question from the HSE pack.

To check any supplier's certificate, run these five steps:

  1. Ask for the certificate, with its number and the name of the issuing certification body.
  2. Search the company name or the certificate number on IAF CertSearch. A free account allows a limited number of checks each day.
  3. Confirm the status is valid.
  4. Confirm the certificate scope covers the activity you are buying, for example design and manufacture of completion equipment, rather than trading or office work alone.
  5. Confirm the certified locations include the plant that will make your equipment.

A certificate that IAF CertSearch does not find may be unaccredited, or the search details may not match, so confirm it directly with the certification body named on it. A certificate whose certified locations do not include the manufacturing plant does not evidence that plant. An OHSAS 18001 certificate is out of date, because ISO 45001 replaced that standard. After the certificate, the questionnaire asks for numbers.

Which incident statistics do operators ask for, and how are LTIF and TRIR calculated

Lost time injury frequency (LTIF) is the number of lost time injuries (fatalities plus lost work day cases) per 1,000,000 hours worked, the basis IOGP uses. LTIF is also written LTIFR, and the LTIFR calculation is the same: lost time injuries × 1,000,000 / hours worked.

The total recordable injury rate (TRIR) on the IOGP basis counts fatalities, lost work day cases, restricted work day cases and medical treatment cases per 1,000,000 hours worked. The US Occupational Safety and Health Administration (OSHA) basis is recordable injuries and illnesses × 200,000 / total hours worked, where 200,000 hours stands for 100 full-time workers at 40 hours a week for 50 weeks.

MetricWhat it countsIOGP basisOSHA basis
LTIF (also LTIFR)Lost time injuries: fatalities plus lost work day casesPer 1,000,000 hours workedPer 200,000 hours worked
TRIRAll recordable injuries: fatalities, lost work day cases, restricted work day cases and medical treatment cases (OSHA also counts recordable illnesses)Per 1,000,000 hours workedPer 200,000 hours worked

Take a plant that records 2 recordable injuries in 400,000 hours worked. Its TRIR is 2 × 200,000 / 400,000 = 1.0 on the OSHA basis and 2 × 1,000,000 / 400,000 = 5.0 on the IOGP basis, so the same record gives a figure five times larger.

Incident statistics are only comparable when they carry their base, the hours worked and the period. Operator questionnaires and platforms commonly ask for the last three years, and some grade a three-year average TRIR. With a small workforce one incident moves the rate sharply, so reviewers read the trend, the hours and the investigation records rather than one year's rate. Near miss reports, inspections and training completion are leading indicators that show the system working when injury counts are near zero, while injury rates are the lagging side, and a reviewer reads leading and lagging indicators together. Operators compare the figures against their own benchmarks and the supplier's trend.

US prequalification platforms such as ISNetworld sometimes ask a supplier outside the US for an OSHA 300 log or an Experience Modification Rate (EMR). The EMR is a US workers' compensation insurance rating and has no equivalent outside US workers' compensation. The supplier provides its statutory accident records instead, with its rates, their base and the hours worked stated. Those statistics come from the plant's activities, and each activity needs a risk assessment.

Need expert guidance on the right solution?

Talk to our engineers about your project requirements.

Book a Consultation

Which risk assessments and method statements does a manufacturer need to show

A manufacturer's risk assessments cover the work done at its own plant (machining, lifting and handling, pressure testing, coating, chemical handling, packing and loading) and the visits it hosts, such as customer inspections and witness tests. The set must match the activities the plant performs. Visitors on the shop floor face the same hazards as the workforce, so hosted visits need their own assessment.

ISO 45001 clauses 6.1.2 and 8.1.2 require hazards to be identified, assessed and controlled. Controls are chosen by the hierarchy of controls: elimination, substitution, engineering controls, administrative controls and, last, personal protective equipment (PPE). Each risk assessment must contain:

  • the activity
  • the hazards
  • who could be harmed
  • existing controls
  • the risk rating
  • further controls, chosen by the hierarchy of controls
  • the residual risk
  • an owner
  • a review trigger

A job safety analysis (JSA) breaks one task into steps and names the hazards at each step. A method statement sets out the sequence of work for a task, with its controls, equipment, competence and permits. Together they are often called RAMS (risk assessments and method statements).

Method statements for work on an operator's site apply only where the supplier's people work on that site, and then they follow the operator's permit to work system. The plant and test bay those assessments describe are what a reviewer goes to see.

What HSE evidence should a completion-tool plant and its pressure-test bay show

A completion-tool plant shows its HSE system through plant records, such as lifting equipment inspections, fire system inspections, safety data sheets (SDS) for the chemicals it uses and waste records, and through a controlled pressure-test bay. This is the plant HSE evidence an auditor looks for on the shop floor.

The pressure-test bay holds the plant's largest stored energy. The UK Health and Safety Executive's guidance note GS4 names the unintentional release of stored energy as the main hazard in pressure testing, and says to pressurise with water or another liquid rather than gas wherever possible. A hydrostatic test uses water for this reason. GS4 also sets out that the test location should be remote enough that no one is at risk, or that an enclosure should contain an unintended release. A test facility that follows these principles shows:

  • a written test procedure
  • liquid as the test medium wherever possible
  • a remote location or an enclosure, with an exclusion zone and barriers
  • gauges in calibration, and kept test records

Each plant's legal register names the laws of its own jurisdiction. For a plant in India, the governing safety law is the Occupational Safety, Health and Working Conditions Code, which replaced the Factories Act and twelve other central labour laws, with rules framed under it state by state. The plant usually also needs consent to operate from the state pollution control board under the Water and Air Acts.

Desktop HSE answers are confirmed by a verification audit at the supplier's site. A site audit walks the shop floor, the test bay and the records behind both, and can run alongside an inspection or witness test visit. The site audit is also where packs like this usually fall short.

Which HSE document problems most often hold up a supplier's approval

Most HSE document problems are mismatches: between the paper and the company, the site, the work or the numbers. These are the seven a reviewer finds, each with its fix.

  1. The HSE policy is unsigned, unrevised, or names a different legal entity or site. Re-sign it under top management in the registering entity's name.
  2. The HSE manual is a template that does not describe how the plant works. Rewrite it around the plant's real processes.
  3. Injury rates arrive without hours worked or a base. State the hours, the base and the period beside every rate.
  4. A certificate has expired, is not accredited, or does not cover the manufacturing site. Check it on IAF CertSearch before submitting.
  5. Risk assessments cover work the supplier does not do, or miss work it does. Rebuild them from the plant's activity list.
  6. There is no legal register for the plant's jurisdiction. List the laws and permits that apply to the site.
  7. Questions in the IOGP 423-01 questionnaire, or in any prequalification questionnaire, are marked "not applicable" with no reason. Justify each one, as IOGP 423-01 requires.

    Each mismatch costs the supplier something: a round of questions, an audit finding, or not being invited to tender. IOGP's guidance tells clients to consider not inviting a contractor with too many gaps, so a clean pack protects the approval itself. Building the pack so these never appear is the next step.

How do you assemble and maintain an HSE pack that passes review

An HSE pack that passes review is built once, indexed to the questionnaire the operator uses, and kept current with signatures, revisions and statistics updated every year. To assemble and maintain one:

  1. Index the pack to the ten IOGP 423-01 elements, so any operator's questionnaire or vendor registration form maps onto it.
  2. Use one legal name, address and site on every document.
  3. Sign and revision-number the HSE policy and the HSE manual, and review both at least once a year.
  4. Update the incident statistics each year, with the hours worked and the base stated.
  5. Keep certificate copies with their numbers and the certification body, and recheck each one on IAF CertSearch before every submission.
  6. Prepare for the verification audit: the people who run each process should be able to show it working.

After the first build, the job is to keep current the signatures, statistics and certificate checks, and to keep the HSE pack in the same folder as the quality documents, because supplier reviews often ask for both together.

The same pack feeds each prequalification platform an operator uses. Achilles runs a self-assessment built on IOGP 423. ISNetworld and Avetta, used together in North America, collect statistics, written programs, training documentation and the EMR. The operator's own registration portal asks for the same records. Results from external certification audits can be offered to avoid answering the same question twice, as IOGP suggests. Knowing what does not belong in the HSE pack keeps it short.

Where does the HSE pack end and the rest of the vendor pack begin

The HSE pack answers how the supplier controls risk to people and the environment where it works, and nothing about whether the product meets its specification. A full vendor pack has four parts, and the boundary between them decides which folder each document goes in.

PackWhat it answersTypical documents
HSE packDoes the supplier control risk to people and the environment?The nine core documents, and any ISO 45001 or ISO 14001 certificate
Quality and product packIs the tool right?A material test report (MTR) for each heat, the inspection and test plan (ITP), pressure test and factory acceptance test (FAT) records, a certificate of conformance
Company and commercial packIs the company real, and can it be paid?Incorporation and tax records, bank details
Export and shipping packWill the consignment clear?Commercial and export documentation

Material test reports, inspection and test plans and acceptance test records belong in the quality pack, not the HSE pack. Each of the other packs has its own guide. Against that boundary, here is what this manufacturer hands over.

What does Maximus OIGA Private Limited provide for an HSE review

Maximus OIGA Private Limited manufactures SpectraMax downhole completion equipment, engineered to order at its plant at Plot 365, Savli GIDC Road, Alindra, Vadodara, Gujarat 391776, India. Its vendor registration documents include HSE documents: the HSE policy, the HSE manual and HSE records. They form part of a complete document set for supplier registration, sent on request.

Customer quality and procurement teams can arrange a plant audit at Vadodara to see the records and the processes behind them. Maximus OIGA Private Limited also completes supplier pre-qualification questionnaires as part of vendor approval.

The quality and product records travel in the same request. Every shipment includes material test reports traceable to the heat, dimensional inspection reports, a pressure test certificate for each unit and certificates of conformance. A reviewer gets all of it by requesting the documents directly.

Frequently asked questions

What are the ISO standards that relate to HSE?

ISO 45001 covers occupational health and safety management and ISO 14001 covers environmental management. Both are management system standards, and a supplier is certified to them by an accredited certification body, not by ISO. ISO 45001 replaced OHSAS 18001, so an OHSAS 18001 certificate is out of date. Check any certificate's status, scope and sites on IAF CertSearch.

What does HSE compliance mean?

HSE compliance means meeting the laws that apply where a supplier works, plus the HSE requirements its customers set, and being able to show it. The evidence is a legal register listing those requirements and a recorded evaluation of compliance against them, which ISO 45001 clause 9.1.2 requires.

What is an HSE prequalification questionnaire?

An HSE prequalification questionnaire is the set of HSE questions an operator sends before it lets a supplier tender. IOGP 423-01 is the industry's model, with ten elements and a scoring system. Desktop answers are then confirmed by audit, so every answer should point to a document the supplier can show.

Is an HSE policy the same as an HSE manual?

An HSE policy and an HSE manual are two different documents. The HSE policy is a short signed commitment by top management to safe and healthy working, legal compliance, protection of the environment and continual improvement. The HSE manual describes how the management system delivers that commitment, site by site and process by process. A reviewer expects both, and expects them to name the same company and sites.

How is LTIFR calculated?

LTIFR is lost time injuries × 1,000,000 / hours worked, and LTIFR and LTIF name the same rate. One lost time injury in 250,000 hours worked gives an LTIFR of 4.0 per million hours. The same record on a 200,000-hour base gives 0.8, so state the base beside the rate every time.

Get to know Maximus OIGAExplore our products, capabilities, and certifications.Learn More

More Information

Related News & Insights

Which API Specification Covers Which Tool, and How to Read a Licence Number

Which API Specification Covers Which Tool, and How to Read a Licence Number

A certificate on a letterhead isn’t proof. This guide maps common completion tools to the API specifications that cover them, explains how an API Monogram licence number is built, and shows how to check it on the API Composite List before a part reaches incoming inspection.

Read More

November 20, 2026

Petrobras Supplier Registration for Oilfield Equipment Manufacturers

Petrobras Supplier Registration for Oilfield Equipment Manufacturers

Which HSE documents an oilfield equipment supplier is asked for at vendor registration, what each one must contain and how operators check them. It covers the HSE policy, manual, registers, emergency plan, and incident and training records.

Read More

November 20, 2026

Sonangol Angola Vendor Registration for Completion Equipment Suppliers

Sonangol Angola Vendor Registration for Completion Equipment Suppliers

How completion-equipment suppliers register to sell in Angola. Registration on the ANPG portal comes first, because only registered suppliers can bid. Sonangol vendor registration comes second and covers Sonangol’s own companies.

Read More

November 20, 2026

NNPC Nigeria vendor registration for oilfield equipment suppliers

NNPC Nigeria vendor registration for oilfield equipment suppliers

How NNPC vendor registration on SAP Ariba and NipeX NJQS qualification work, and why the bidder is in practice a Nigerian-registered company. Written for Nigerian bidders and the overseas makers who supply them: who files what, how Nigerian content is scored, and how SpectraMax tools clear into Nigeria.

Read More

November 20, 2026

Markets We Supply: Lead Times, Export Documentation and Field References

Markets We Supply: Lead Times, Export Documentation and Field References

Maximus OIGA builds SpectraMax completion tools to order at its Vadodara plant. It ships to India, the Middle East, Southeast Asia and the US, with quality records and export papers included in every order.

Read More

November 20, 2026

The documentation pack an operator will ask you for

The documentation pack an operator will ask you for

What a downhole tool's documentation pack must contain — mill test reports, heat traceability, the ITP and certificate of conformity — and nine checks to run before you sign off.

Read More

October 20, 2026

Best cement retainer and float equipment manufacturers in Asia

Best cement retainer and float equipment manufacturers in Asia

Seventeen cement retainer and float equipment makers in Asia: nine make retainers, fourteen float equipment, six both. Compared on seven points, unranked, every claim sourced.

Read More

October 20, 2026

Best bridge plug manufacturers in Asia

Best bridge plug manufacturers in Asia

Thirteen bridge plug manufacturers in Asia — China, India and the UAE — compared on seven points, across drillable, retrievable, composite and dissolvable plug types.

Read More

October 20, 2026

Best packer manufacturers in the Middle East

Best packer manufacturers in the Middle East

Twelve oilfield packer makers for Gulf wells: five build in the Gulf, seven ship in from India and China. Compared on six points, unranked, every claim sourced.

Read More

October 20, 2026

Best liner hanger manufacturers in Asia

Best liner hanger manufacturers in Asia

Eleven liner hanger manufacturers in Asia — four in China, six in India, one in the UAE — compared on seven points, from spec data and lead times to field running support.

Read More

October 20, 2026